Bunn 41167.0001B Coffeemaker دليل المستخدم

Bunn 41167.0001B Coffeemaker دليل المستخدم لجهاز

Bunn 41167.0001B Coffeemaker دليل المستخدم

ومقتطفات من محتويات

محتوى موجز على الصفحة لا 1

INSTALLATION & OPERATING GUIDEBUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (217) 529-6644To ensure you have the latest revision of the Operating Manual, or to view the Illustrated PartsCatalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, atwww.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog andmanual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1

محتوى موجز على الصفحة لا 2

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYBunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal serversand Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor.2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:a) Electronic circuit and/or control boards - parts and labor for 3 years.b) Compresso

محتوى موجز على الصفحة لا 3

CONTENTSWarranty .............................................................................................................2Introduction ........................................................................................................3User Notices .......................................................................................................3Electrical Requirements ......................................................................................4Plumbing Requirements .....

محتوى موجز على الصفحة لا 4

ELECTRICAL REQUIREMENTSCAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.120 VOLT Model230 VOLT CE Model230 VOLT UK ModelNote: This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate conductor for chassis ground.Electrical Hook-UpCAUTION – Improper electrical installation will damage electronic compone

محتوى موجز على الصفحة لا 5

PLUMBING REQUIREMENTSThese brewers must be connected to a cold water system with operating pressure between 20 and 90 psi(138 and 620 kPa) from a ½˝ or larger supply line. A shut-off valve should be installed in the line before thebrewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345kPa). The water inlet fitting is .75-11.5 NH (HOSE THREAD). For convenience an elbow adaptor is providedto convert to a ¼˝ flare fitting. Bunn-O-Matic

محتوى موجز على الصفحة لا 6

INITIAL SET-UP1.2.3.4.5.5.6.7.Place a large empty cup under the brew chamber.Connect the brewer to the power source.Water will flow into the Hot Water tank and stop whenthe tank is filled to its capacity.Open, then close door with switch (See illustration)Press the Large Brew Switch. Water will flow into theBrew tank. Some excess water will flow into the cup.Wait approximately ten minutes for the water in the tankto heat to the proper temperature. Display will show"HEATING" until tank reaches it

محتوى موجز على الصفحة لا 7

OPERATIONCOFFEE BREWING1. Place cup under brew chamber FIG 8-1. (Slide booster out for small cups) FIG 8-3.2. Press the OPEN/CLOSE switch to open pod door FIG 8-2.3. Press fresh pod firmly down into pod holder FIG 8-3.4. Press the OPEN/CLOSE switch to close pod door FIG 8-2.5. Press the desired brew switch.6. Once the brew cycle is finished, display will read "BREWING COMPLETE", remove cup after display returnsto main screen.FIG 8-4HOT WATER DISPENSING1. Place cup under brew chamber FIG 8-1. (Sl

محتوى موجز على الصفحة لا 8

CLEANINGSPRAYHEAD1. Open the pod door with the "OPEN/CLOSE" switch.2. Disconnect brewer from power source and allow to cool.3. Unscrew sprayhead counterclockwise (looking from below). Fig 8-14. Remove sprayhead and seal from holder.5. Check and clean the sprayhead. The sprayhead holes must always remain open. Clean all the holes in theplastic sprayhead to remove any mineral deposits. Wash and rinse in sink. Fig 8-26. When reassembling sprayhead, be sure to have seal installed with ridge facing u

محتوى موجز على الصفحة لا 9

TANK DRAININGFACTORY BLOWOUT1. Disconnect the power and water supply to brewer. Allow brewer to cool before proceeding.2. Remove 2 screws that secure the top cover. Remove the cover. Place brewer next to a sink.3. Disconnect the hose from (top) center hose barb of each tank. Connect a piece of ¼" ID hose (aproximately12" long) in place of the ones you just removed. FIG. 9-14. Lay the brewer on it's back, with new hoses in sink.5. Connect the brewer to the power source.6. Press hidden switch unt

محتوى موجز على الصفحة لا 10

PROGRAMMING SWITCHESHIDDEN SWITCHPress until display reads"BREW LOCKOUT"HIDDEN SWITCHStep forward throughscreensHOT WATER"YES" or (+)OPEN/CLOSE"NO" or (-)SMALL BREW (B)SteSte backwards throughStepscreensLARGE BREW (A)"DONE"Page 1041167.1 051508

محتوى موجز على الصفحة لا 11

PROGRAM OVERVIEWBREW LOCKOUT (YES/NO)Setting to "YES" will only allow brews at or above the"SET READY" temp screen.SET PULSE BREW (A/B)Individually adjust on/off times.BREW TYPE (A/B) (Tea/Coffee)Tea setting provides less "purge" after brew cycle.AIR TIME (A/B) (1-25)Time the brew tank is purged at the end of each brewcycle.BREW OZ. (A/B) (1-16)Adjust brew volume.DRIP TIME (A/B) (OFF/1-50)Time between brew cycle and pod ejection.BREW METER (A/B) (1-5)Simplified pulse brew adjustment.1=Preinfusio

محتوى موجز على الصفحة لا 12

ADJUSTMENTS & OPTIONAL SETTINGSBREW TYPE ABREW LOCKOUT ?NODONEYESTEABREW METER A: 2-+BREW METER A: 2-+SET PASSWORD00SET TEMP:(-)DONE0200°(+)HOT H2O TEMP 200°(-)DONE(+)BREW OZ A:DONE COFFEEDONE COFFEEENTER SERVICE #?NO(-)0SET LANGUAGE ?YESSET READY:(-)DONE195°(+)H2O READY: 190°(-)DONEPage 12(+)DONE(+)6.0(+)ENTER PASSWORDYESNODONEBREW OZ B:BREW TYPE BTEA(-)8.000UNITSMETRIC DONE ENGHOT H2O LOCKOUT ?NODONEYESENTER ASSET # ?NOYES41167.1 011609

محتوى موجز على الصفحة لا 13

ADJUSTMENTS & OPTIONAL SETTINGS (CONT.)SetPulseBrew A ?NODONEYESSetPulseBrew B ?NODONEYESBREWS TO EMPTY(-)25(+)BREW COUNT ##NOYESCalibrateMaximumNO H2O TIME? YESSERVICE TOOLS ?NOYESAIR TIME A: 17.0(-)DONE(+)DRIP T I M E A: 5(-)AIR TIME B: 17.0(-)DONE(+)Enabl EnergySavrNODONEYESBREW COUNT ##RESETNUMBER OF EJECTSDOUBLE(+)DRIP T I M E B: 5(-)DONE(+)AIR PUMP POWER 4(-)DONE(+)CALIBRATE FLOW ?NONEXTSINGLEDONEYESSEAL REPLACED ?NOYESFACTORY DEFAULTSAutoPOD BREWERNOVERSIONYESPage 13xx.xx41167.1 011609

اترك التعليق