Roberts Gorden HE40DL Heating System دليل المستخدم

Roberts Gorden HE40DL Heating System دليل المستخدم لجهاز

Roberts Gorden HE40DL Heating System دليل المستخدم

ومقتطفات من محتويات

محتوى موجز على الصفحة لا 1

FOR YOUR SAFETYIf you smell gas:1. Open windows.2. DO NOT try to light any appliance.3. DO NOT use electrical switches.4. DO NOT use any telephone inyour building.5. Extinguish any open flame.6. Leave the building.7. Immediately call your local gassupplier after leaving the building.Follow the gas supplier’sinstructions.8. If you cannot reach your gassupplier, call the Fire Department.WARNINGBlackheat HE®Vacuum AssistedLinear, Double Linear,U-Tube, and Multi-BurnerGas Fired Heating SystemsIns

محتوى موجز على الصفحة لا 2

TABLE OF CONTENTSSECTION 1: Heater Safety ............................................21.1 Manpower Requirements ....................................21.2 IP55 Protection ....................................................21.3 Safety Labels and Their Placement ....................2SECTION 2: Installer Responsibility............................42.1 Low Level User Instructions................................42.2 Corrosive Chemicals...........................................42.3 National Standards

محتوى موجز على الصفحة لا 3

TABLE OF FIGURESFigure 1: Bottom and Back Panel Label Placement ........2Figure 2: Control Side Label Placement..........................3Figure 3: Linear & Double Linear, Horizontal Mounts......6Figure 4: Linear & Double Linear, One Side Reflector ....6Figure 5: Linear & Double Linear, Two Side Reflectors ...6Figure 6: Linear & Double Linear, 45° Mount ..................6Figure 7: Linear & Double Linear, 2 Foot Deco Grille,Protective Grille ................................................7Figu

محتوى موجز على الصفحة لا 4

Product ApprovalROBERTS GORDON® appliances have been tested and CE certified as complying with the essentialrequirements of the Gas Appliance Directive, the Low Voltage Directive, the ElectromagneticCompatibility Directive and the Machinery Directive for use on natural gas and LPG when installed,commissioned and maintained in accordance with these instructions.These instructions refer to appliances designed to operate in the European Union.Appliances designed for other countries (Non-European U

محتوى موجز على الصفحة لا 5

BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUALSECTION 1: HEATER SAFETY1.1 Manpower RequirementsYour Safety is Important to Us!To prevent personal injury and damage to the heater, twopersons will be required for installation.This symbol is used throughout the manualto notify you of possible fire, electrical or burnhazards. Please pay special attention whenreading and following the warnings in thesesections.1.2 IP55 ProtectionThe burner is certified to protection class of IP55. Thismeans

محتوى موجز على الصفحة لا 6

SECTION 1: HEATER SAFETYFigure 2: Control Side Label PlacementDescriptionLogo LabelWiring Diagram LabelPart Number91033200910314043 of 73

محتوى موجز على الصفحة لا 7

BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUALSECTION 2: INSTALLER RESPONSIBILITY• To install the heater, as well as the gas and electricalsupplies, in accordance with applicable specificationsand codes. Roberts-Gordon LLC recommends theinstaller contact a local Building Inspector or FireMarshal for guidance.• To use the information given in a layout drawing andin the manual together with the cited codes andregulations to perform the installation.• To install the heater in accord

محتوى موجز على الصفحة لا 8

SECTION 3: CLEARANCES TO COMBUSTIBLESSECTION 3: CLEARANCES TO COMBUSTIBLESWARNING• Consult local Building Inspector, Fire InsuranceCarrier or other authorities for approval of proposedinstallation when there is a possibility of exposure tocombustible airborne materials or vapours.• Hang heater in accordance to the minimumsuspension requirements on Page 11, Section 5.Fire HazardKeep all flammable objects, liquids andvapors the minimum required clearances tocombustibles away from heater.Some o

محتوى موجز على الصفحة لا 9

BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUAL3.2 Clearances Data - Linear and Double LinearNOTE: 1. All dimensions are from the surfaces of all tubes, couplings, tees, elbows and crosses.2. Clearances B, C and D can be reduced by 50% after 7500 mm of tubing downstreamfrom the burner.3. All measurements are in millimeters.ModelHE15STHE30DLHE20STHE40DLHE25STHE50DLHE30STHE60DLHE35STHE70DLHE40STHE45STHE50STFIGURE 3: LINEAR & DOUBLE LINEAR, HORIZONTAL MOUNTSA150150150150150150200200B890970

محتوى موجز على الصفحة لا 10

SECTION 3: CLEARANCES TO COMBUSTIBLESNOTE: 1. All dimensions are from the surfaces of all tubes, couplings, tees, elbows and crosses.2. Clearances B, C and D can be reduced by 50% after 7500 mm of tubing downstreamfrom the burner.3. All measurements are in millimeters.HE30STHE60DLHE35STHE70DLHE40STHE45STHE50STDHE25STHE50DLBHE20STHE40DLCHE15STHE30DLAModelFIGURE 7: LINEAR & DOUBLE LINEAR, 2 FOOT DECO GRILLE, PROTECTIVE GRILLEA150150150150150150200200B89097097010201170122012801330C15701650165017801

محتوى موجز على الصفحة لا 11

BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUAL3.3 Clearances Data - U-TubeNOTE: 1. All dimensions are from the surfaces of all tubes, couplings, tees, elbows and crosses.2. Clearances B, C and D can be reduced by 50% after 7500 mm of tubing downstreamfrom the burner.3. All measurements are in millimeters.4. Add 60 mm clearance to uncovered u-tube..HE25UTHE30UTHE35UTHE40UTHE45UTHE50UTDCHE20UTBHE15UTAModelFIGURE 10: U-TUBE, HORIZONTAL MOUNTA150150150150150150200200B8909709701020117012201

محتوى موجز على الصفحة لا 12

SECTION 3: CLEARANCES TO COMBUSTIBLESNOTE: 1. All dimensions are from the surfaces of all tubes, couplings, tees, elbows and crosses.2. Clearances B, C and D can be reduced by 50% after 7500 mm of tubing downstreamfrom the burner.3. All measurements are in millimeters.4. Add 60 mm clearance to uncovered u-tube.HE25UTHE30UTHE35UTHE40UTHE45UTHE50UTDCHE20UTBHE15UAModelFIGURE 14: U-TUBE, OPPOSITE 45° TILTA200200200250250275300300B13701530153016301780183018801930C15001650165018601960204021102160D560

محتوى موجز على الصفحة لا 13

BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUALSECTION 4: MAJOR COMPONENT DESCRIPTIONSBurner (shown with TubeGasket)Must be installed with theflame observation windowfacing down.Reflector(Aluminium orStainless Steel)Alternate overlap asshown on overview.Minimum overlap is 160 mm.Burner TubeTubeFan Tube with Internal SwirlerSupplied in 3000 mm lengths.Burner tube is always the firsttube after the burner.Heat treated aluminised tubesupplied in 3000 mm lengths.Supplied in 3000 mm lengths.

محتوى موجز على الصفحة لا 14

SECTION 5: GENERAL SUSPENSION DETAILSSECTION 5: GENERAL SUSPENSION DETAILSWARNINGSevere Injury HazardSecure burner to burner tube with bolts andlockwashers.Hang heater with materials with a minimumworking load of 75 lbs (33 kg).Failure to follow these instructions can resultin death, injury or property damage.WARNINGCut/Pinch HazardWear protective gear during installation,operation and service.Edges are sharp.Failure to follow these instructions can resultin injury.To ensure your safety, and com

محتوى موجز على الصفحة لا 15

BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUALFigure 17: Critical Hanger PlacementTypical Suspension DetailsBeamClampI-BeamConcreteBeamAnchorI-BeamWasher10 mmRod600 mmminimum*Screw Hookmin. 10 mmWasherLocknutWoodBeam300 mmminimum*BowShackleTurnbuckle(not included)* Allows for thermal expansion of system.Bow ShackleSide ViewHangerHanger100 mmMax.DescriptionBurner TubeS-hookSpring HookBow ShackleTube/Reflector Hanger12 of 73Part Number030511009190730291903300E000757603090100Front View45

محتوى موجز على الصفحة لا 16

SECTION 6: LINEAR & DOUBLE LINEAR HEATER INSTALLATIONSECTION 6: LINEAR & DOUBLE LINEAR HEATER INSTALLATIONWARNINGCut/Pinch HazardWear protective gear during installation,operation and service.Edges are sharp.The figures in this section provide a general overview ofcomponent placement in a Linear and Double Linearsystem. The location of some components such assupports and couplings is crucial for proper installation.Assemble the heater components as shown on Page 14,Figure 18.For optional reflect

محتوى موجز على الصفحة لا 17

Vent Cap orBird Screen14 of 73BurnerReflector End CapReflector SupportTube ClampPackageBurner TubeTube and Reflector HangerCouplingOutside WallFresh AirSupplyReflector*NOTE: Locate fan away from wet environmentor use the IP54 protected fan.Fan TubeInternal Swirler(Required for Multiburner)Damper Assembly(For Single Heater)Fan Assembly*Weld SpotU-ClipsBLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUALFigure 18: Linear General Assembly Overview

اترك التعليق